AussieAssembly and Use ManualFOR YOUR SAFETYIf you smell gas:1. Shut off gas to the appliance.2. Extinguish any open flame.3. Open Lid.4. If odor cont
•GRIDS(Item #1)CERAMICBRIQUETTES(Item #2)STEP 10 - INSTALL CERAMIC BRI-QUETTE TRAYS/ COOKING GRIDSReference Diagram on Page 21•In upright position, fr
11FIG. D - Bottom Cylinder BracketFIG. C. - Top Cylinder BracketSTEP 13 - ATTACH LP CYLINDER TO GRILL•Remove the protective cap from the LP Cylinderv
Step 14 - LEAK TESTING (TO BE PERFORMED IN A WELL-VENTILATED AREA.)Supplies Needed for a Leak TestClean paint brush, water, and dishwashing liquidHow
OPERATING AND MAINTAINING YOUR GAS GRILLGAS, CYLINDER, HOSE ANDREGULATOR INFORMATIONThis LP gas grill was designed to use propane gas. Propanecylinder
14· Never connect or disconnect LP gas cylinder or fittings while grill is in use or is hot. · When the LP gas cylinder is connected, the grill must
15· Always perform a leak test before each use.· Leak test must be performed in a well ventilated area. · Never perform a leak test on a grill while i
· Wash the porcelain coated Cooking Grids (1) with amixture of hot water and baking soda. · Empty the foil pan and grease tray after each cookingsess
· Open Hood before lighting the grill to prevent an explosion from gas build-up. · Always inspect the gas hose and regulatorassembly before each use.
Your burners have been preset by the manufacturer foroptimal flame performance. A blue flame, possibly with asmall yellow tip, is the result of the op
Regularly clean your LP gas grill between uses and espe-cially after extended periods of storage. Ensure the grilland its components are cool before
2IMPORTANT SAFEGUARDSFAILURE TO FOLLOW THESE SAFEGUARDS COULD RESULT IN DEATH, SERIOUSBODILY INJURY, AND/OR PROPERTY LOSS. READ AND FOLLOW ALL INSTRUC
20It is not necessary to remove and wash the ceramic bri-quettes in order to keep them clean. Burning off the residueafter each cooking should be suff
21Assembly Diagram
12345678910GridCeramic Briquette TrayBurnerCotter PinHandleSpacer, HandleBolt, M6x80Grill Body Assy.Screw, #8x1/2Regulator/ HoseQTY.223 or 43 or 41221
242122232425Track, LeftCylinder Bracket BottomBolt, Black M6x15Panel, Left SideNut M6113012603.6269.0003.6227.0003.6208.0003.6271.0003.6209.0003.6269.
25QTY.3-BURNER PARTNUMBER4-BURNER PARTNUMBERPART/ DESCRIPTON3940SpacerBolt, Black M6x110mm8803.4074.0003.4066.0003.4074.0003.4066.0041Wing Nut 6M 8 03
26TROUBLESHOOTING ProblemPossible CauseSolutionBurners will not light using the igniterBurners not assembled cor-rectlyNot pausing long enoughbefore c
TROUBLESHOOTING ProblemFlames blow outFlare upPersistent grease fireUnable to fill LP tankHumming orwhistling from theregulatorPossible CauseHigh or g
28IMPORTANT NOTICEIMPORTANT NOTICEThe Gas Grill is setup to operate with a LP Gas Cylinder equippedwith an OPD (Overfilling Prevention Device).This i
AUSSIE GRILL COMPANYLIMITED WARRANTYThis product is warranted to the original consumer purchaser against defects in material and workman-ship under no
7. WARNING! If your grill catches on fire:8. Check the Bottom Body Panel for grease buildup.Remove excess grease to avoid a grease fire in the pan.
— NOTICE —AUSSIE GRILL COMPANY STRIVES TO BE A QUALITY SUPPLIER OF CONSUMER PRODUCTS. IF WE INADVERTENTLY OMITTED ANY PARTS NEEDED FOR ASSEMBLY, OR YO
Assembly InstructionsNOTE: Refer to Assembly Diagram on pages 21 and 22. It may be easier to position grill on itsback side for assembly. Do not tight
6•Place Side Table(14) over Left SidePanel(24) and secure by installing twoM6X15 screws through side table and intothreaded hole. Completely tighten
M5X10ScrewItem#29STEP 6 - INSTALL DOOR1. Bottom Panel (Item#33) 9 Bolts & Nuts2. Top Panel (Item#36) 7 Bolts & Nuts3. Cente
M4x12Flat HeadScrewItem#15M4NutItem#44M4x10BoltItem#17 STEP 7 - INSTALL TRAY(Reference Assembly Diagram page 22.See Track Detail)A)•Secure Right Track
FIG. AFIG BCOTTER PIN(Item #4)BURNER(Item #3)Holes in FrontFirewallGas NozzleControl ValveManualLightingGas Collectorand ElectrodeVenturi end ofBurner
Comments to this Manuals