Aussie 6804T80SS1 Specifications

For Outdoor Household Use Only. Not for Commercial Use.Need Help? Need to Register Your Grill? Looking for Aussie Parts & Accessories?Visit us onl

10To reduce the risk of bodily injury from lifting, the following assembly steps #s 9 and 10 will require two people.CAUTION!Step 11Hood/Body To Cart

11Prior to performing any further assembly, PERFORM “FIRST TIME USE” LEAK TEST as detailed on pages 17-18. If the grill is fully assembled before perf

12Step 14Side Burner Igniter Wire ConnectionThe Side Burner Igniter Wire is pre-installed and connect-ed to the Ignition Box. Attach the wire to the S

13Step 15A. Side Burner Control Knob AssemblyAlign the flat keyed hole in the Control Knob with the keyed stem of the Side Burner Valve. Push the Cont

14To reduce the risk of a laceration hazard:• Wear protective gloves when installing warming rack. Hood and Bowl edges could be sharp.CAUTION!Step 17W

15Connecting/Disconnecting the GasUsing GasCarbon Monoxide Hazard• This appliance can produce carbon monoxide which has no odor. Using it in an enclo

16LP Hose and RegulatorTo reduce the risk of serious bodily injury or death from fire or explosion:• Clean and inspect the gas hose/regulator before e

17Before Using Your LP Gas GrillInstallation CodesTo reduce the risk of serious bodily injury or death from fire or explosion:• This installation must

18How to Perform A Leak Test “FIRST TIME USE” and as requiredSupplies Needed for a Leak Test:• Clean paint brush• Water• Dish washing liquid1. Use an

197. If “growing” bubbles appear on any of the connection points, you have detected a gas leak. Immediately close the LP Gas Cylinder valve by turning

2NOTICEMeco Corporation strives to be a quality supplier of consumer products. If we omitted any parts needed for assembly, or you need troubleshootin

20Should you notice that your Burner(s) are getting hard to light or the flame is not as hot as it once was, refer to the “How to Clean your Burners”

215. Push the Igniter Button in until the Burner is lit. Listen for the spark ignition, and look to make sure the Burner is lit. If no spark, see Trou

22Manually Lighting the GrillTo reduce the risk of serious bodily injury or death from fire or explosion:• Open Hood before lighting the grill to prev

23Lighting the Side BurnerTo reduce the risk of serious bodily injury or death from fire or explosion:• Open Side Burner Lid before lighting the grill

241. Open the Side Burner Lid.2. IMPORTANT: Make sure Side Burner Control Knob is turned “Off” first.3. Turn the LP Gas Cylinder valve open counterclo

25Cooking On the Gas GrillTo reduce the risk of serious bodily injury or death from fire, explosion or burn hazard:• Never use charcoal or lighter flu

26Roasting (Indirect Method)To reduce the risk of burns from the hot air and steam trapped inside:• Open the Hood carefully when roasting on grill.WAR

27Rotisserie CookingRotisserie Cooking:The constant turning of the meat while cooking allows it to self baste with natural juices, making food cooked

28Warming RackTo reduce the risk of fire or flare-up from grease drippings:• When cooking food on the warming rack, make sure no Burners are on direct

29Care and MaintenanceCAUTION!Cleaning the GrillBottom Panel, Grease Pan, Foil Pan: Remove the two bolts on the sides securing the Bottom Panel. (Step

3Packing ListDescription Warming RackCooking Grid, 3 pcs.Flavor Activators - 4 large, 3 smallGrease PanFoil PanLeft Side Shelf with Side BurnerSide Bu

30Remove nuts and bolts.How to Clean the Burners1. Make sure the Control Knobs are turned “Off” and the grill is completely cooled.2. Carefully remove

315. Use a pipe cleaner to clear insect nests from the inlet hole of Main Burner (Fig. 19) and Side Burner tube. (Fig. 20)6. Open up the Main Burner h

32StorageTo reduce the risk of serious bodily injury or death:• Store your LP gas grill in a cool dry place. Do not store an LP Gas Cylinder in a spac

33EmergenciesProblemGas leaking from cracked/cut/burned hoseGas leaking from LP Gas CylinderGas leaking from LP Gas Cylinder valveGas leaking between

34TroubleshootingProblemBurners will not light using a matchLow flame or low heatFlames blow outPossible CauseRegulator coupling nut is not fully conn

35ProblemFlare upPersistent grease fireUnable to fill LP tankHumming or whistling from regulatorCabinet doors do not closePossible CauseGrease build-u

36If you need replacement parts, refer to the Parts Illustra-tions to find the exact parts you need. If you have any questions or need help, contact C

37Parts ListKey Description Quantity1 Side Burner Cover 12 Side Burner Cooking Grid 13 Left Side Table 14 Side Burner Valve 15 Side

38Limited WarrantyMECO CORPORATION - LIMITED WARRANTYThis product is warranted to the original consumer purchaser against defects in material and work

4ContentsPacking Lists ...3Preparation for Assembly ...

5Assembly InstructionsStep 1Caster AssemblyLay Cabinet Bottom Panel upside down, so that the flat surface is on the floor. Assemble Fixed Casters to t

6 7Step 3Side Panel AssemblyAttach Left Side Panel and Right Side Panel to Cabinet Bottom Panel with six 1/4-20 x .50” Bolts and 1/4-20 Nuts. Secure L

7Step 5Cabinet Upright AssemblyAttach Cabinet Upright to Cabinet Bottom and Front Crossbar with four 5/32 x .31” Bolts. Orient Upright so that Match-h

8Step 7Door Handle AssemblyAssemble Handle to Left Door using two 5/32 x .31” Bolts. Repeat with Right Door.Note: 2 extra screws provided.Step 6A. Cyl

9B. Drawer PositioningSlide Drawer Assembly over the Drawer Tracks to position the Drawer.Step 9 Model 6805 & 6804 with drawerA. Drawer Assembly